/ REGISTER HERE shopping cart 0 Item(s)
sculpture supply
sculpture supply canada about us contact us ordering events news techinical info videos media
» Dragon Skin 10 Very Fast
» Dragon Skin 10 Fast
» Dragon Skin 10 Medium
» Dragon Skin 10 NV
» Dragon Skin 10 Slow
» Dragon Skin 20
» Dragon Skin 30
» Dragon Skin FX-PRO
» EcoFlex 00-10
» EcoFlex 00-20
» EcoFlex 00-30
» EcoFlex 00-35
» EcoFlex 00-50
» EcoFlex GEL
» Encapso K
» Equinox 35 Fast (Food Safe)
» Equinox 38 Med (Food Safe)
» Equinox 40 Slow (Food Safe)
» EZ Brush Vacuum Bag Silicone
» Mold Max 10T
» Mold Max 14NV
» Mold Max 15T
» Mold Max 20
» Mold Max 25
» Mold Max 27T
» Mold Max 29NV
» Mold Max 30
» Mold Max 40
» Mold Max 60
» Mold Max Stroke
» Mold Max XLS II
» Mold Star 15 Slow
» Mold Star 16 Fast
» Mold Star 19T
» Mold Star 20T
» Mold Star 30
» Mold Star 31T
» Oomoo 25
» Oomoo 30
» PoYo Putty 40
» Rebound 25 Brush-On
» Rebound 40 Brush-On
» Rubber Glass
» Silicone 1603
» Silicone Starter Kits
» Smooth-Sil 936
» Smooth-Sil 940 (Food Safe)
» Smooth-Sil 945
» Smooth-Sil 950 (Food Safe)
» Smooth-Sil 960 (Food Safe)
» Solaris Encapsulation Silicone
» Solaris Primer
» Sorta-Clear 12
» Sorta-Clear 18 (Food Safe)
» Sorta-Clear 37 (Food Safe)
» Sorta-Clear 40 (Food Safe)
Home : Rubber Silicones : Smooth-Sil 950

Call for Pricing

*All prices are in Canadian funds.


Smooth-Sil 950 Drum Kit 550Lb (799068)
Smooth-Sil™ 950 is a Platinum Silicone (addition cure) with a shore hardness of 50. Smooth-On Platinum Silicones (platinum curative) cure at room temperature with no shrinkage. These silicones exhibit good chemical, abrasion and heat resistance. Materials such as plasters, concrete, wax, low-melt metal alloys or resins (urethane, epoxy or polyester) can then be cast into these silicone rubbers without a release agent. Smooth-Sil™ Platinum Silicones are used for rapid prototyping, wax casting (foundries and candle makers), architectural restoration and for casting concrete. Smooth-Sil™ 950 is Food Grade compliant. Size: Drum Kit 550Lb

Smooth-Sil 950 is suitable for making baking molds and trays, ice trays, casting butter, chocolate and other applications used to produce foods. Smooth-Sil 950 has been tested by an independent laboratory to comply with the total extractive limits when properly processed and heat cured. Refer to the Smooth-Sil Platinum Series technical bulletin for proper processing instructions for Smooth-Sil 950 (available at www.smooth-on.com).
Wash mold cavity thoroughly with dishwashing detergent/water solution. Rinse thoroughly and allow drying before using.

Compliance - The ingredients and ingredient levels in Smooth-Sil 950 comply with 21 CFR 177.2600, rubber articles for repeated use subject to the total extractive limits as specified and published in the Code of Federal Regulations. FDA compliance does not mean that Smooth-Sil 950 is FDA approved.

Using Mold For Baking
· Place mold on a baking sheet for greater stability and handling.
· Do not expose rubber to temperatures above 400° F / 204° C. Do not subject molds to the broiler.
· Silicone rubber does not distribute heat evenly. Food in shallow molds will bake faster vs. deep draft molds. Thick sections will retain heat longer than thin sections. Check frequently for doneness on first use.
· Clean molds with soapy warm water and a soft sponge and rinse thoroughly between batches or prior to storing. You can dry the mold quickly in an oven. Bake for 5 minutes at 300°F / 150°C.